|
Twin Hose for
Pressure Pots
 Twin
Hose is flexible polyurethane with a nylon inner
tube for solvent resistance. Comes
with 1/4" and 3/8" reusable fittings with stainless steel inserts.
The two hoses are welded together, eliminating the use of duct tape and
cable ties. Very neat! Hoses are sold with instructions for cutting
the hoses and re-attaching fittings for specific configurations.
#A5906 - Twin Hose 5' for
pressure tank - 50.00
#A5906 - Twin Hose 6' for
pressure tank - 53.00
#A5910 - Twin Hose 10' for pressure tank - 60.00
#A5912 - Twin Hose 12' for
pressure tank - 65.00
#A5915 - Twin Hose 15' for pressure tank - 75.00
#A5925 - Twin Hose 25' for pressure tank - 97.00
#A59xx - Custom length twin hose. Multiply length desired by
2.50 and add 40.00
#59014 - Replacement 1/4" fitting - 10.20
#59038 - Replacement 3/8" fitting - 10.20
Air and Fluid Hoses
 Rubber
Air and Fluid Hoses
Red air hose is 5/16" or 3/8" (inside diameter) and black
fluid hose is 1/4" or 3/8". For sheer sensitive products and runs over 25
ft, we suggest 3/8" for both hoses. Tough rubber hoses are very flexible and tough. Both hoses
have standard Binks/Devilbiss style reusable fittings (3/8" fluid, 1/4" air).
Use the 3/8" air for runs of 25' and over in HVLP applications.
Rubber Air
Hose - 5/16"
#5305 - Air hose 5' - 17.85
#5315 - Air hose 15' - 33.15
#5325 - Air hose 25' - 49.45
#53xx - Custom length hose - (Multiply length desired by 1.65 and add $10.00)
#12-301 - Reusable fitting for 5/16" air hose - 5.00
Rubber Air
Hose - 3/8"
#5405 - Air hose 5' - 19.00
#5415 - Air hose 15' - 37.00
#5425 - Air hose 25' - 56.00
#54xx - Custom length hose - (Multiply length desired by 1.85 and add $10.00)
#12-303 - Reusable fitting for 3/8" air hose - 5.00
Rubber Fluid Hose
- 1/4"
#5505 - Fluid hose 5' - 19.75
#5515 - Fluid hose 15' - 39.25
#5525 - Fluid hose 25' - 59.75
#55xx - Custom length hose with fittings - (Multiply length desired by
2.10 and add $10.00)
#12-306 - Reusable fitting for 1/4" fluid hose -
5.00
Rubber Fluid Hose
- 3/8"
#5615 - Fluid hose 15' - 49.00
#5625 - Fluid hose 25' - 62.00
#55xx - Custom length hose with fittings - (Multiply length desired by
2.50 and add $12.00)
#12-302 - Reusable fitting for 3/8" fluid hose -
6.00
 New!!
- Economy Rubber
Air Hose with Hi-Flo HVLP Fittings
Red air hose is 1/4" (inside diameter) This tough
rubber hose comes with our Hi-FLO HVLP quick disconnects installed and are
compatible with most other systems like Porter-Cable, Campbell Hausfeld and
others.
Economy Rubber
Air Hose
- 1/4"
#H15AH - Air hose 15' - 25.00
#H25AH - Air hose 25' - 35.00
Premium Lightweight Poly
Air Hose
Red nylon/polyurethane air hose is 1/4" (inside diameter) Tough
poly hose is lightweight yet durable and strong. Includes spring guards for
anti-kinking. Runs longer than 15' with HVLP systems should only be done with
adequately sized compressors.
Rubber Air
Hose - 1/4"
#5705 - Air hose 5' - 32.00
#5715 - Air hose 15' - 42.50
#5725 - Air hose 25' - 54.00
#57xx - Custom length hose - (Multiply length desired by 1.30 and add $26.00)
#59014 - Replacement 1/4" fitting - 10.20
#34050 - Replacement spring guard - 3.00
Premium Fluid Handling Hose
Black fluid hose is our best. Inner polyamide
hosing is reinforced with a synthetic braided yarn and then a tough outer cover
of non-marring polyurethane is applied. All stainless fitting and anti-kink
spring guards will withstand the toughest applications. Excellent for
waterbornes and all solvent applications.
Premium
Fluid Hose - 1/4"
#5805 - Fluid hose 5' - 35.20
#5815 - Fluid hose 15' - 51.00
#5825 - Fluid hose 25' - 66.00
#57xx - Custom length hose - (Multiply length desired by 1.75 and add $30.00)
#76-458 - Replacement 3/8" fitting - 12.00
#34014 - Replacement spring guard - 3.00
Twin Hose or
Pressure Pots
HI-FLO
Connectors & Couplers
 These
"Hi-Flow" quick connectors (see comparison photo - right) are larger in diameter than
standard connectors. Recommended for all HVLP systems. Fittings will work
with most common fittings like Porter Cable and Campbell Hausfeld, but we recommend they be
purchased in matched sets (with matching Coupler) as they may not work with
all manufacturer's couplers. These couplers do not require that you
retract the sleeve when inserting the disconnect. Simply push the disconnect
in, and the sleeve on the coupler automatically retracts and snaps back in.
A - #A8273 - 1/4"
Male Quick Coupler - 7.00
B -
#A8271 - 1/4" Female Quick Coupler - 7.00
C -
#A8272 - 1/4" Male Quick Connector - 2.00
D -
#A8270 - 1/4" Female Quick Connector - 2.00
Reusable
Fittings
A -
#12-306 - Binks/Devilbiss style fitting for air hose - 5.00 (fits 3/8" OD, 5/16" ID Hose)
#12-303 - 5.00 (fits 11/16" OD, 3/8"
ID)
B - #12-301 - Binks/Devilbiss style reusable fitting for fluid hose -
5.00
(compression style fits 1/2" OD, 1/4" ID Hose)
C - #59014 - Replacement 1/4" fitting - 10.20 (insert style
fits 3/8" OD, 1/4" ID Hose)
D -
#59038 - Replacement 3/8" fitting - 10.20 (insert style fits
3/8" OD, 1/4" ID Hose)
Miscellaneous
Fittings
A- #12-402 - 1/4"NPT male to 1/4" swivel female union -
4.00
B -
#12-221
-
1/4" NPS male to male nipple
- 2.00
C- #1011538 - 1/4" female to 3/8" male reducer fitting - 4.00
#70-220 - 1/4" swivel for air line (attaches to gun air
inlet) -
30.00
Filters/Regulators
Finish
Filters
 #W1425 -
215 US mesh
Stainless Steel Filter for suction guns - 7.00 ea.
(fits fluid pickup tubes up to 1/2")
#72-550/60 - 3/8" Inline 3 pc. Filter for gun fluid
inlet 60 mesh -
32.00 (Not for Airless)
#72-550/100 - 3/8" Inline 3 pc. Filter for gun fluid inlet 100 mesh -
32.00 (Not for Airless)
#36-009 - Replacement 60 mesh filter - 7.60
#36-005 - Replacement 100 mesh filter - 7.60
 #QSNSG - 100 mesh
micro-filter for gravity guns (fits Asturo, QualSpray and most other guns
with a 7/16" fluid inlet (pkg. of 10) - 20.00 ea.
Water/Oil
Filters
 QualSpray
Disposable In-line Filter - this filter
removes oil, water, rust, dirt and other particles that get through other
downstream filters. It's designed for low restriction of air so you can
install it right at the gun and won't affect low pressure guns like LVLP and
HVLP. A very economical way to remove the last trace of contaminants before
they enter the gun.
#F3 - PRICE: $3.75
(each)
 QualSpray
Transparent In-line Filter - removes air line water before it can get into your gun
or pressure tank. Easily mounts right at the tool air inlet to provide the
best protection. Water is purged by depressing a small plunger and the
filter can be taken apart and cleaned if necessary. Item is bi-directional.
#QS-F1 - PRICE: $25.00
 QualSpray
In-Line Desiccant - When you need to remove all traces of water
vapor and oil, this economical in-line desiccant works just like the
expensive wall mount units. Uses silica to remove every trace of oil and
water and changes from blue to pink when it needs to be changed. Item comes
with 1 extra silica change and has 1/4" female and male connections. Item
works best when a water extractor is installed before unit to remove liquid
water in line. Unit is bi-directional.
#QS-D1 - $20.00
 QualSpray
Economy Regulator/water filter - traps water, and
contaminants. Inline design allows mounting to a compressor output or
wall (bracket included). 1/4" inlet and outlet with manual drain. Large
regulator gauge is easy to see. The best in filtration at a great price.
#QS200FR -
$49.95 Regulator/water filter with
regulator and gauge
 QualSpray
Professional Regulator/filter - traps 99% water, and oil and
contaminants down to 5 micron. Large body design allows mounting to a wall
or support it on the ground with the optional metal stand (shown). 120 cfm
flow capacity and 300 psi maximum pressure. 1/2 NPS inlet and 1/4 NPS outlet
with shut off valve. Large self-relieving regulator reads accurate pressure.
Manual drain. The best in filtration at a great price. Best when used 25' or
more downstream of compressor.
#QS614FR -
$145.00 Regulator/filter with
regulator and gauge
#QS01FH - $25.00 Heavy Duty Metal
Holder for above
 CA
Technologies Air Treatment System consisting
of:
1. Pre-filtering element for elimination
of condensation and particulates.
2. Oil separating (coalescing) filter for removal of oil and
residual contaminants.
3. 2 - 1/4" outlets with shut off valves, 1 regulated, 1
non-regulated.
Air inlet - 1/2"
#52-522 - $499.00
 CA
Technologies Filter/Dryer System consisting
of:
1. Filtering element for elimination
of condensation and oil particulates.
2. Dessicant dryer for removal of water vapor.
3. 1 - 1/4" outlets with shut off valve regulated.
#52-531 - $499.00
#52-554 - First stage cartridge replacement -
$145.00
#52-555 - Second stage cartridge replacement -
$99.00
Air Flow
Regulator
 #QS03
- Air Regulator with gauge (for
connecting to spray gun at inlet) -
32.50
The regulator with gauge
shown attached to a spray gun (not included) allows you to
regulate air very precisely right at the gun, where it matters most. Can be
used with gravity feed and pressure feed systems as well.
1/4" threaded male (on input) and 1/4" female (on
output). Gauge calibrated
0-150 psi. Diaphragm type regulates air more
consistently. Glass lens.
#QS03SP
- Air Regulator with gauge (for
connecting to spray gun at inlet) 0-25psi or 0-60psi - smaller
increments for lower pressure guns -
35.00 (1/4" threaded male (on input) and 1/4" female (on
output). Gauge calibrated
Diaphragm type regulates air more
consistently. Glass lens.)
#R-11
- Super- Mini Regulator with gauge
(for
connecting to spray gun at inlet) -
30.00
This regulator is about 1/2
the size of a standard gun regulator like the QS-03. Ideal for the smaller
footprint of detail guns or whenever you want to use a smaller regulator. Can be
used with gravity feed and pressure feed gun with a 1/4" thread. .
1/4" threaded male (on input) and 1/4" female (on
output). Gauge calibrated
0-150 psi. Diaphragm type regulates air more
consistently. Glass lens.
R-11 Super
Mini-Regulator vs. QS-03 Regulator
Bottom and Gravity Feed
Cups
Bottom Feed Cups
 QS-68C1 - 1
Qt. QualSpray™ Aluminum Cup for
siphon feed and pressure feed guns with standard 3/8" fluid inlet.
Feature cam-lock and non-drip air vent with easy to clean inner splash guard. Good design
at an economical price. 25.00
QS-68C2 - 1
Qt. QualSpray™ Aluminum Cup
same as above but bayonet top closure system (no cam lock)
25.00
 #45-1235
(Bedford Part#) - Non drip 1
Qt. Aluminum Cup for guns with a 3/8" NPS swivel fluid inlet. Exclusive
directional vent tube assure non-drip operation and easy cleaning. Leather
gasket. Similar to Binks #81-350. 37.00
 QS-32D - Pressurized 1
Qt. QualSpray™ Aluminum Cup for ECO/SSP
and other pressure feed guns with standard 3/8" fluid and 1/4" air fittings.
With
air regulator and pressure regulator for cup pressure. 129.00
With this setup, you can
spray thicker finishes with less thinning, and get faster delivery rates and
fan patterns. This is a great add-on for all ECO/SSP, ECO/I, BRP, and BRI/A
guns. It installs easily and allows you to adjust cup pressure. Will fit any
gun with a standard 3/8" threaded material inlet and 1/4" air inlet.
#QS-32 - QualSpray 1 Qt. Pressurized Cup with single regulator (regulates
pot pressure) - 99.95
#QS-32D
- Same as above but with dual regulators (regulates
gun and pot pressure) - 129.95
#QS-32NR
- QualSpray 1 Qt. Pressurized Cup (no regulator) -
50.00
(includes check valve and
tubing)
Gravity Cups for Detail Guns
A:
#QS-125ALC - 125 ml polished aluminum
cup w/ press in plastic top.- $15.00
(Fits most gravity guns with a female thread-on cup).
B:
#QS-2004C
- 400ml polished aluminum
cup w/ screw in lid (contains gasket) - $20.00
(Fits most gravity guns with a female thread-on cup).
Suction Cup for Detail Guns
 #QS-08CUP -
8 oz aluminum
cup w/ yoke assembly top - $7.50
(Fits most import detail suction guns with a
1/4 fluid inlet).
Gravity Cups for Standard Size Guns
A:
#QS-600ALC - 600ml polished aluminum
cup w/ press in plastic top.- $25.00
(Fits most gravity guns (including Asturo) with a female thread-on cup.
Thread size: M16 x 1.5)
B:
#QS-600NYC
- 600ml nylon
cup w/ screw on plastic top.- $20.00
(Fits most gravity guns (including Asturo) with a female thread-on cup.
Thread size: M16 x 1.5)
Also available as
400ml size for $20.00 (#QS-400STC)
A:
#QS-1000STC - 1000ml polished aluminum
cup w/ screw on metal top w/ gasket - $30.00
(Fits most gravity guns (including Asturo) with a female thread-on cup.
Thread size: M16 x 1.5)
B:
#QS-600STC
- 600ml polished aluminum
cup w/ screw on metal top w/ gasket - $28.00
(Fits most gravity guns (including Asturo) with a female thread-on cup.
Thread size: M16 x 1.5)
Cleaning
 #QS813
Basic Cleaning Kit - 24.95
This kit has the basic brushes and micro brushes
for general gun maintenance. Good for gravity, touch up and siphon guns.
Includes:
12" pick up tube cleaning brush
1/4" twisted bristle brush
1/2" twisted bristle brush
Detail end brush
Nylon bristle parts brush
5 pc. miniature brush set
6 pc. precision needle set
 #QS820
HVLP Cleaning and Servicing Kit - 29.95
This kit has the basic brushes and micro brushes
for general gun maintenance and servicing. Good for gravity, touch-up and siphon guns.
19 pc. kit comes in a clear plastic tube for easy storage.
Includes:
A - 1/2" twisted bristle brush
B - O-ring removal tool
C - Gun Lube
D - 12" pick up tube cleaning brush
E - 1/4" twisted bristle brush
F -
6 pc. precision needle set
G -
5 pc. miniature brush set
H - Nylon bristle parts brush
I - Detail End Brush
 #QS814
Master HVLP Maintenance Kit - 45.00
Includes:
Brass pick up tube brush
12" pick up tube brush
6 pc. micro needle set with handle
3 pc. detail end bush with handle
5 pc. twisted mini brush set
Large nylon brush for general parts cleaning
1/4" and 1/2" brushes for cleaning body cavities and air passages
Gun lube
Items are packed in a
convenient flip top plastic case.
This kit is designed to
provide you with the necessary specialized tools to clean every area of your
HVLP spray gun or pressure pot system. An absolute must for maintaining your gun
properly. This system is the one used by professional repair and rebuilding
shops.
 The
5 piece Mini-Brush set in all the Cleaning Kits above gets
the most use. Customers asked for replacements so here they are - 5
replacement mini-brushes on a ring.
#BQ-M05 - PRICE:
$5.00
 O-Ring
Removal Tool
is an absolute must for removal of o-rings and seals without damaging gun
body or threads. Offset design with grip.
#H816 - O-Ring Tool - 2.50
Spray Gun Lubricant
is an absolute must for proper gun maintenance. Handy pinpoint type allows
for precise application of oil. Oil is silicone free and white mineral oil
based. Won't affect finishes.
#H811 - Gun Lube - 2.50
Miscellaneous
 Ford #4 Viscosity Cup for precise measurement of
finish viscosity. Long handle and a brass orifice for precision. A conversion chart to other popular sized cups is
available
here.
#97-9101 -
Viscosity Cup Ford #4 - 17.95
 Stainless Viscosity Cup for precise measurement of
finish viscosity. Sturdy, indestructible and easy to clean. Conforms to
Iwata NK-2. A conversion chart to other popular sized cups is
available
here.
#VC-02 -
Viscosity Cup Ford #4 - 35.00
New!!
Ford #4 Economy Viscosity Cup for precise measurement of
finish viscosity. Differs from above with a shorter handle and plastic
orifice. Similar to cups shipped with Turbine systems like Fuji.
#QS-817 -
Economy Viscosity Cup Ford #4 -
$5.00
A Mil Gauge is necessary for measurement of wet finishes. Instructions
for use are on the reverse of this metal gauge. Use for determining dry mil
thickness.
#A8231 - Mil Gauge - 2.95
 Universal Gravity Spray Gun Holder and filling station holds both
gun and strainer (left)
for easy filling and will
swing out of the way once the cup is filled. Can be used with or without
mounting screws (supplied) on a flat surface so it's mobile. Comes with
holder for both mini and full sized gravity guns.
#QS-815 - Gravity Stand -
18.95
 Magnetic Gravity Spray Gun Holder
supports two gravity guns. Large magnets hold it securely to ferrous metal
surfaces. Holders are non-marring plastic covered and two hose holders are
included. Painted metal construction.
#GH-06 - Gravity Holder -
20.00
BACK TO TOP
Copyright © 2011 Homestead Finishing Products All
rights reserved. |
