|

Team up your favorite
pressure feed gun with our QualSpray Pressure pots and cups. A Homestead exclusive,
we've put these pots through the paces and found them to be rugged and
dependable. All pressure pots are tested before shipping and come complete
with setup, use and troubleshooting instructions. For hoses and
fittings click
here.
Pressure pots are available in standard
construction or all-stainless
where the situation requires it.
1 Q
NOTE: When waterborne products are
left in a non all-stainless pressure pot, you may experience corrosion in
the tank lid. This is unavoidable. If you perform diligent cleaning after
using waterbornes and do not leave the product in the tank, it should not be
a problem. However, if corrosion is an issue, we recommend you consider
all-stainless steel tanks.
1 QT.
PRESSURE POTS
QS-32
This 1 quart pressurized cup converts any pressure feed gun to a pressurized
cup feed. If you have a standard siphon feed or remote pressure cup feed
gun, convert it with this pot to spray thicker finishes or increase finish
delivery rates. Polished aluminum cup, brass pickup tube and single
regulator with check valve included. Not recommended for frequent spraying
of acid catalyzed finishes.

Construction:
lightweight aluminum
Regulator: single flow-through
Check Valve: Nylon with Viton seals
Capacity: 32 oz. (1 quart)
Working pressure: 0-15 psi.
#QS-32 PRICE: $109.95

A dual regulator assembly lets you
control both primary atomizing air and air pressure to the cup. Cup pressure
regulator range is 0-10 psi. Recommended
when you have long air lines (25 ft. and over) from your compressor.
#QS-32D PRICE: $139.95
#QS-32NR - Cup only w/ lid and
check valve:
$55.00
#QS-32CUP - Replacement cup bottom only: $20.00
#QS-32CG - Replacement Gasket:
$1.50
#QS-32CV - Replacement Check Valve: $4.00
#QS-32LPD - Replacement splash guard -
$1.50
#L1Q-40 -
1 quart liners (package/40) -
$8.00
#HW-SS-S - 3 pack fine mesh stainless barrel strainers (fits over pickup
tube) - $10.00
#QS32SRA - Replacement regulator assembly for QS-32 (single
regulator) - $55.00
#QS-32DRA - Replacement dual regulator assembly
-
$85.00
2 QT.
PRESSURE POTS
QS-64T This economical pot is a great way to get into remote pressure feed
spraying. The lightweight design and narrow mouth make is well-suited for
holding in your hand or slinging it from your belt with the hook. Features a
lockable, heavy duty regulator that is better and more accurate than our old
QS64A and other similar 2 qt pots. Features a recessed check valve assembly
for easier cleaning and maintenance, shut
off valve on the fluid outlet, and the solvent proof rubber gasket has more "give" than the hard white
gaskets found on similar pots at this price for better sealing. Works with all
finishes but is not recommended for frequent use with acid catalyzed
finishes. (see the QS-64TSS or QS-64ES below).

Construction:
lightweight aluminum
Pickup Tube: brass
Regulator: single (shown) or dual* flow-through
Capacity: 64 oz. (1 quart)
Working pressure: 0-50 psi.
#QS-64 PRICE: $125.00
#QS-64D (dual regulators) PRICE:
$145.00
#QS-64TG -
Replacement Gasket:
$9.00
#QS-64TCV - Replacement Check Valve: $6.50
#L2QT-40 -
2 quart liners (package/40) -
$10.99
#W4405 - 5 pack fine mesh stainless steel barrel strainers (fits over pickup
tube) - $24.00
QS-64S
With this rugged pot you'll upgrade (from the QS64T above) to a wider mouth
for easy cleaning and stainless steel pickup tube. A better choice for water
base and acid catalyzed finishes. Your choice of single or dual regulators.
The Bandit
anti-tip-over stand also works with this pot if you put it on
the floor.

Construction:
lightweight aluminum and stainless steel
Regulator: single (shown) or dual flow-through
Cup & Capacity: Teflon coated, 64 oz. (2 quart)
Working pressure: 0-50 psi.
#QS-64S PRICE: $169.00
#QS-64SD (dual regulators) PRICE:
$199.00
#QS-64S07 - Replacement Gasket:
$6.99
#QS-64SCV - Replacement Check Valve: $6.50
#W4405 - 5 pack fine mesh stainless steel barrel strainers (fits over pickup
tube) - $24.00
QS-64ES
With this rugged pot you'll upgrade from the 2 qt pots above to a wide
mouth and easier clamping system. We've also
designed in stainless steel where it counts, on the pickup
tube and the fluid outlet. No up-charge for stainless steel fittings! This
gives you Teflon and stainless for all wet parts so it's the best for water base,
catalyzed and other corrosive finishes that attack brass and aluminum. Your choice of single or dual regulators.
Pot requires use of QS-EXT air inlet extension when using barrel style
in-line filters at pot air inlet. This pot does not have an inner liner, so
get the plastic liners below to make cleanup easier.
An all-stainless version is available for those
situations that require it.

Construction:
Teflon coated steel and 304 stainless steel
Regulator: single (shown) or dual flow-through
Cup & Capacity: 2 liter (2.1 quart)
Working pressure: 0-50 psi.
#QS-64ES PRICE: $289.00
#QS-64ESD (dual regulators) PRICE:
$319.00
#QS-64ESG - Replacement Gasket:
$20.00
#QS-64ESCV - Replacement Check Valve: $15.00
#W4405 - 5 pack fine mesh stainless steel barrel strainers (fits over pickup
tube) - $24.00

QS-64ESD -
2 quart, dual regulated pressure pot.
1 GALLON PRESSURE POT
QS-128S
This rugged pot quickly became our favorite pressure pot here at Homestead.
If you want the ruggedness of a 2 gallon pot but can't justify the size,
this is the pot to get. Great features include Teflon coating for chemical
resistance, stainless pickup tube and fluid output and large wing nut
clamping system. Stainless inner pail is removable for easy cleaning*.
Features a heavy duty self-relieving regulator for precise control. Works
with all finishes and is highly recommended for water base and catalyzed
finishes. Pot is wide enough to place a 1 quart finish can inside. Pot
available with air agitator.
Construction: Teflon coated steel shell and top
Pickup Tube: Stainless steel
Regulator: single, self-relieving diaphragm flow-through
Capacity: 1.3 gallon
Working pressure: 0-80 psi.
#QS-128S - single regulator PRICE:
$319.00
#QS-128SD dual regulator PRICE:
$349.00
#QS-128SA - single regulator, air agitator PRICE:
$599.00
#QS-128SAD - dual regulator, air agitator PRICE:
$629.00
#QS-1284 -
Replacement Gasket:
$20.00
#L2G-20 -
1 gallon plastic liners (package/20) -
$10.99
(not for air agitated versions)
#W4405 - 5 pack fine mesh barrel strainers (fits over pickup) - $24.00
2-1/2 GALLON
PRESSURE POTS

QS-288/QS640 The
QualSpray™ 2½ and 5 gallon non-ASME pot is our most rugged and feature packed
pressure pot. It's wide opening allows you to put a gallon can of finish
inside. The tank body comes with casters, and is Teflon coated inside and
out. Large wing nuts make it easy to seat the top to the body and its low,
squat design is virtually tip-over proof. Item is shipped with our own
supplemental instructions for goof-proof setup and maintenance. Pots
available as single or dual regulated and with an optional air agitator.
When you need rugged dependability this is the pot to
get.
Construction:
Teflon coated steel and stainless steel
Regulator: single (shown) or dual flow-through
Fluid Pickup: Stainless Steel
Capacity: 2½ gallon, 5 gallon
Working pressure: 0-80 psi. (NON-ASME)
#QS-288S (2-1/2 gallon, single regulator) PRICE:
$379.00
#QS-288D (2-1/2 gallon, dual regulators) PRICE:
$399.00
+SU - add stainless steel fluid outlet w/ shut off to above:
$35.00
The QualSpray™
2-1/2 gallon pots are available with an air agitator built in to agitate finishes (photo
right). Same quality features as above, it has an air motor with
regulator, stainless steel stir shaft and a tough nylon blade. Compatible with all finishes,
including acid catalyzed lacquers and varnishes. You won't find a better
price if you compare this pot feature to feature with the competition!
#QS-288SA (single regulator, air agitator) PRICE:
$559.00
#QS-288DA (dual regulator, air agitator) PRICE:
$579.00
+SU - add stainless steel fluid outlet w/ shut off to above:
$35.00
#QS-28884 - Replacement Gasket:
$22.00
#QS-288PA - Replacement Pickup Assembly: $6.50
#QS-288FS - Replacement Filter Screens:
$7.50 (pack of 5)
#51-231-10 - Heavyweight plastic liners (4 mil) - $35.00
(pack of 10)

#51-261-12 - Rigid polyethylene liners -
$34.50 (pack of 12)
5 GALLON
PRESSURE POTS
QS-640 The
QualSpray™ 5 gallon non-ASME pot has the
same great features as our smaller 2-1/2 gallon. It fits most of the popular
5 gallon metal and plastic pails.* All 5 gallon pots have stainless inner
tank liner, fluid pickup tube and fluid outlets (2). The tank body comes with casters, and
has side handles to make it easy to
pick up. Large wing nuts make it easy to seat the top to the body and its low,
squat design is virtually tip-over proof. Item is shipped with our own
supplemental instructions for goof-proof setup and maintenance. Pots
available as single or dual regulated and with an optional air agitator.
Pots feature dual fluid outputs and refill inlet.
#QS-640S (5 gallon, single regulator) PRICE:
$479.00
#QS-640D (5 gallon, dual regulators) PRICE:
$499.00
* Inside bottom tank
dimensions 15-1/2" H x 12-1/2" W.

The QualSpray™
5 gallon pots are available with an air agitator built in to agitate finishes (photo
right). Same quality features as above, it has an air motor with
regulator, stainless steel stir shaft and a tough nylon blade. Compatible with all finishes,
including acid catalyzed lacquers and varnishes. You won't find a better
price if you compare this pot feature to feature with the competition!
#QS-640AD (same as
above but 5 gallon, dual regulator, air agitator) Fits most 5 gallon pails.
PRICE:
$779.00

All stainless-steel construction
is required when purity is required or where corrosion may be
a problem. All stainless is perfect for waterbornes that are left for
extended periods of time in the tank. A Homestead exclusive, we've put these
pots through the paces and found them to be rugged and dependable. All
pressure pots are tested before shipping and come complete with setup, use
and troubleshooting instructions.
Construction:
304 stainless steel
Regulator: single or dual flow-through
Agitator Shaft & Blade: stainless steel
Cup & Capacity: 2 qt - 5 gallon
Working pressure: 0-80 psi.



1
QT SERIES

New!!
- All stainless-steel construction
is traditionally expensive, but we've solved that problem
with our all-new 1 qt Homestead exclusive! Upgrade your current cup whether
it's an old style suction feed or pressure feed. This is the cup to use with
water based finishes! Can replace any cup with a traditional 3/8" NPS fluid
fitting. Features an EPDM* solvent proof gasket and cam lock closure.
Now you don't have to worry about
leaving water based finishes in the cup - whether it's all day or all week.
Traditional aluminum cups not only can react with some water based
finishes, but they also are hard to clean. Water based finishes are much
easier to clean from stainless steel, particularly latexes and the pigmented
lacquers and polyurethanes.
* EPDM - ethylene propylene diene
monomer, a synthetic rubber gasket that is more solvent proof and softer
than typical hard Teflon gaskets used in 1 qt cups.

You can convert any standard pressure feed gun, whether
it's a compressed air or turbine! Shown at the left is an Accuspray #10
turbine gun with the QS-32SS/P stainless cup.
|
 |
#QS-32SS/S - Suction feed
design with vent hole on cover. Comes with anti-drip splash guard
and EPDM gasket. For use with all guns that have a 3/8" NPS fluid
fitting.
PRICE:
$129.95 |
|
 |
#QS-32SS/P - Pressurized cup
design for all guns that use air to pressurize cup. either from gun
head or air regulator. Comes with 1/8" barb swivel fitting on cover
so you can orient pressure hose in any direction, check valve,
anti-drip splash guard and EPDM gasket. For use with all guns that
have a 3/8" NPS fluid fitting.
PRICE:
$159.95 |
 |
#QS-32SS/PR - Same as above
but with an air regulator to pressurize cup. Pressure gauge reads
0-15 psi for ultra precise regulation. This cup can convert any gun
with a 3/8" NPS fluid fitting to a pressure feed gun!. Comes
with pressure regulator, 1/8" barb swivel fitting on cover so you
can orient pressure hose in any direction, check valve, anti-drip splash guard
and EPDM gasket.
PRICE:
$199.95 |
2 QT SERIES

New!!
-All stainless-steel construction
is traditionally expensive, but we've solved that problem
with our all-new 2 qt Homestead exclusive! Upgrade your current 2 qt or
purchase it with a system. Available as single or dual regulated, this pot
is still lightweight enough for those that like to hold the pot in their
free hand or hook on a belt. All stainless is perfect for 2 component
catalyzed finishes and waterbornes that are left for
extended periods of time in the tank.
#QS-64TSS - (lightweight - can be hand-held) single regulator $350.00
#QS-64TSSD (lightweight - can be hand-held) dual regulators
$380.00
2
QT & 1.3 GALLON SERIES
#QS-64ESS - 2 qt, single regulator $560.00
#QS-64ESSD 2 qt, dual regulators
$580.00
#QS-64EAS - 2 qt, single regulator, air agitator -
$699.00
#QS-64EASD - 2 qt, dual regulator, air agitator -
$729.00
1.3 GALLON SERIES
#QS-128ESS - 1.3 gallon, single regulator $619.00
#QS-128ESSD 1.3 gallon, dual regulators
$639.00
#QS-128EAS - 1.3 gallon, single regulator, air agitator
$829.00
#QS-128EASD - 1.3 gallon, dual regulator, air agitator -
$849.00
2.5 GALLON
SERIES
#QS-288ESS - single regulator $919.00
#QS-288ESSD dual regulators
$949.00
#QS-288EAS - single regulator, air agitator
$1269.00
#QS-288EASD - dual regulator, air agitator -
$1299.00

5 GALLON SERIES
#QS-640ESS - single regulator $1179.00
#QS-640ESSD dual regulators
$1199.00
#QS-640EAS - single regulator, air agitator $1319.00
#QS-640EASD - dual regulator, air agitator $1339.00
Copyright © 2011 Homestead Finishing Products All
rights reserved. |