QualSpray HVLP Spray Guns and Pressure Pots

QualSpray™ is our exclusive line of spray guns, pressure pots and accessories imported directly by Homestead. Most of these products are designed or configured to our specifications. The spray guns provide a low cost alternative to our other product lines, but without sacrificing quality. All products are pre-tested here before they're shipped out and they come complete with supplemental instructions written by us to get you up and running or for future troubleshooting. For the price conscious spray user or for second guns for specific tasks, these products will perform.

QS-200 "SmartPak" - This little gun package is a great bargain at just under 150.00. It's perfect for small projects, toning, shading and working up samples. We love it here at Homestead for applying water based dyes. SmartPak includes 125cc cup, 400cc cup, 1.2mm & 0.8mm nozzles sets and a Mini Regulator. Will handle all stains and thin clears like shellac and lacquer as well as thinned waterbornes and lacquers. Great for luthiers. Package also includes wrench, 1 stainless steel strainer, cleaning brush and complete instructions.

Body: anodized aluminum
Cup: Aluminum 125cc
Nozzle/needle: stainless steel

Air cap: nickled brass
Gaskets: Teflon
Working Pressure : 43 psi (at gun inlet)
Air Consumption: 2 cfm
Needle/nozzle/air cap: 0.8 & 1.2mm. (1.0mm also available)

#QS-200 - $149.95

#QS-20010 - 1.0mm NN setup for QS200 - $30.00

QS-125WB - We asked our factory to design us a radically different detail gun that could act like a larger one when it came to spraying waterborne and solvent-borne clears. Now you can get a gun that's just as good as spraying thinner viscosity finishes for touch up and detail work, and spray clears without thinning. This new addition has an all stainless steel finish travel path (see description below for QS-600WB), in addition to the stainless used on the nozzle and needle. Plus it only needs 4 cfm to run. The 1.2mm will spray clear finishes without thinning unless they are pretty thick. The 600cc cup will hold larger amounts of finish when you need it. We beta-tested this gun with several customers. Read what one said:

Jeff,

I used the spray gun today, to apply USL to unfilled walnut; all I can say is the gun exceeded my expectations. My pancake compressor was able to keep up and the volume of finish from the gun was impressive. In the past, I’ve been a little heavy handed when spraying finishes, which is why I’ve stuck to brushing, but this gun laid down a nice even finish despite operator inexperience. After just three quick coats, and I’m left with a finish that looks like it had the grain filled, and will only require a minor rubout. In short, I’m one satisfied customer.

Rob Millard

#QS-125WB - $149.00 (standard setup is 1.2mm)
#QS-125WBKIT#1 - $229.00 (Includes 0.8, 1.2 & 1.5mm setups, regulator, repair kit, all in a plastic case see below)
#QS-125WBKIT#1B - $229.00 (Includes 1.0, 1.2 & 1.5mm setups, regulator, repair kit, all in a plastic case see below)
#QS-125WB-KIT#2 - $260.00 (Includes QS125WBKIT#1 above, plus the QS820 Cleaning Kit, A8231 Mil Gauge & QS-817 Viscosity Cup)
#QS-125WB-KIT#2B - $260.00 (Includes QS125WBKIT#B above, plus the QS820 Cleaning Kit, A8231 Mil Gauge & QS-817 Viscosity Cup)

#QS-125/0.8 - 0.8mm NN set - $42.50
#QS-125/1.0 - 1.0mm NN set - $42.50
#QS-125/1.2 - 1.2mm NN set - $42.50
#QS-125/1.5 - 1.5mm NN set - $42.50

Note: In 2010, the fluid fitting on the QS-125WB was changed from a female fitting to a male fitting. Please let us know which style you have on your QS-125WB when ordering a new or spare cup.

#QS-125NYC - replacement 125ml nylon cup - $25.00
#QS-125ALC - replacement 125ml aluminum cup - $15.00 (SALE - WHILE SUPPLIES LAST)
#QS-125/200ALC - 200cc aluminum cup - $28.00
#QS-125/400ALC - 400cc aluminum cup - $28.00
#QS-125/600NYC - 600cc nylon cup - $30.00
#QS-125/600ALC - 600cc aluminum cup - 32.00
#QS-125/MINI-START - 3m PPS Mini-Cup "starter set".
Includes 1 mini 6 oz cup #16115, 10 #16114 lids and liners, &PPS adapter - $50.00

QS-600WB This new gun was built to Homestead's specifications for our customers that wanted a great performing gun for both solvent and waterborne finishes that won't break your budget. This gun incorporates stainless steel in the fluid passages, threaded connector to the cup, and the female connector in the nylon cup. (see below). This upgrade by our factory insures proper performance with waterborne finishes and catalyzed solvent products. Available as a gun only or in kits. We have sold over 200 of these guns in the past 3 years and not one has been returned for any reason!

Body: Teflon/aluminum
Cup: Nylon 600cc standard, others available
Nozzle/needle/fluid passages: stainless steel Best Seller!
Air cap: chrome/brass
Gaskets: Teflon
Working Pressure : 29 psi (at gun inlet)
Air Consumption: 6 cfm

"Jeff, that is an awesome gun! I got a perfect finish spraying Latex with the 2.5 tip with almost no overspray. I switched to the 1.8 tip for the shellac and a waterborne urethane and the finish laid out smooth with very little overspray. The off-the-gun look and feel of the waterborne is great…..I think I have a new favorite finish! Thanks for the help."

Brian Hankins

The QS-600WB-KIT#1 comes in a handy case with extra NN setup, mini-regulator (not shown), service wrench, cleaning brush, filters and rebuild kit.

#QS-600WB - Gun only (choose from 1.0, 1.3, 1.4, 1.6, 1.8, 2.0 & 2.5mm setups) - $159.00
#QS-600WB-LATEX - QS-600WB gun setup for latex spraying with mini-regulator - $189.00
#QS-600WB-KIT#1 - QS-600WB gun, 1.4mm & 1,8mm setup, min-regulator - $229.00
#QS-600WB-KIT#2 - $260.00 (Includes QS600WBKIT#1 above, plus the QS820 Cleaning Kit, A8231 Mil Gauge and QS-817 Viscosity Cup)

#QS-60010 - 1.0mm NN kit for QS600 & QS600WB - $49.95
#QS-60013 - 1.3mm NN kit for QS600 & QS600WB - $49.95
#QS-60014 - 1.4mm NN kit for QS600 & QS600WB - $49.95
#QS-60016 - 1.6mm NN kit for QS600 & QS600WB - $49.95
#QS-60018 - 1.8mm NN kit for QS600 & QS600WB - $49.95
#QS-60020 - 2.0mm NN kit for QS600 & QS600WB - $49.95
#QS-60025 - 2.5mm NN kit for QS600 & QS600WB - $49.95
#QS-600RK - Rebuild kit for QS600 & QS600WB - $15.00
PPS/MED-START - 3m PPS Medium Cup "starter set".
Includes 1 medium cup, 10 lids and liners and adapter (available only with gun purchase) - $55.00

#QS-600/125NYC - 125cc nylon cup - $25.00
#QS-600/125ALC - 125cc aluminum cup - $15.00 (SALE - WHILE SUPPLIES LAST)
#QS-600/200ALC - 200cc aluminum cup - $28.00
#QS-600/400ALC - 400cc aluminum cup - $28.00
#QS-600/600NYC - 600cc nylon cup - $30.00
#QS-600/600ALC - 600cc aluminum cup - 32.00
#QS-600/1000ALC - 1000cc aluminum cup - 35.00

AM-6008 "SmartPak" - This new addition is the pressurized cup version of our popular QS-600WB above. Standard features include stainless needle, nozzle and fluid passages. Gun comes in either pressurized 1 qt cup or remote pressurized cup configuration. Also available as a gun only. Whichever version you buy you get 3 needle nozzle setups, 1.0mm, 1.3mm & 1.5mm. These setups will spray everything from stains and sealers to latex paint. No guesswork or fussing over which sizes to get. Other features include built in air micrometer, fully adjustable fan width control and super light weight. Package also includes wrench, cleaning brush and complete instructions.

Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Working Pressure : 29 psi (at gun inlet)
Air Consumption: 6 cfm
Needle/nozzle/air cap: 1.0, 1.3 and 1.5mm (all 3 included with purchase)

AM-6008/SSP - Gun only (in case) with 3 NN setups - $219.00
AM-6008/XX - Gun only (no case) with 1 NN setups - $169.00 (state nozzle choice xx from sizes here)

AM-6008/1QT - Gun with 1 qt pressurized cup (shown right), 1.0mm, 1.3mm, 1.5mm NN setups, repair kit, strainers, service wrench - $299.00

#AM-6008/10 - 1.0mm NN kit for AM-6008 - $49.95
#AM-6008/13 - 1.3mm NN kit for AM-6008 - $49.95
#AM-6008/15 - 1.5mm NN kit for AM-6008 - $49.95
#AM-6008/18 - 1.8mm NN kit for AM-6008 - $49.95
#AM-6008/20 - 2.0mm NN kit for AM-6008 - $49.95
#AM-6008/25 - 2.5mm NN kit for AM-6008 - $49.95

#AM-6008/CV/3 - 3 pack replacement check valves with tubing - $16.25
#AM-6008/CG/3 - 3 pack replacement cup gaskets - $7.50
#AM-6008/SG/3 - 3 pack replacement cup splash guards - $7.50
#AM-6008/CPCK - cup parts care kit, 3 each gaskets, splash guards and check valves - $29.00 (10% discount)
#AM-6008/SS/5 - 5 pack stainless steel strainers - $24.00
#AM-6008/CUP - replacement cup assembly (top, bottom and check valve) - $55.00
#AM-6008/CBOT - replacement cup bottom only, no top - $15.00
#AM-6008/PR - complete pressure regulator assembly with gauge and check valve - $50.00

New! AM-5008 "SmartPak" - Want a gravity gun that will spray all finishes? This package contains all the nozzles required to spray the most popular waterbased and solvent based finishes and it works with small compressors. The 1.3mm setup in the large gun will handle most clears, stains and sealers and the 1.8 covers the higher solids solvent based low VOC clears and thicker waterbased finishes. The 2.5 covers you on latex paint spraying. Also included are rebuild/service kits, mini-regulator and cleaning brushes. What a great deal this package is if you don't know what nozzles to get for you new gun. Gun incorporates stainless steel in the fluid passages, threaded connector to the cup, and the female connector in the nylon cup. This upgrade by our factory insures proper performance with waterborne finishes and catalyzed solvent products.

Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Cups: 600cc (other sizes available)
Working Pressure : 29 psi (at gun inlet)
Air Consumption: 6 cfm
Needle/nozzle/air cap: included in kit, 1.3mm, 1.8mm & 2.5mm

AM-5008 - Gun with 600cc cup (shown left) 1.3mm, 1.8mm, 2.5mm NN setups, repair kit, strainers, service wrench - $269.00

#HW-SS-3G - 3 pack replacement stainless steel strainers - $7.50
#AM-5008/125NYC - 125cc nylon cup - $25.00
#AM-5008/125ALC - 125cc aluminum cup - $15.00 (SALE - WHILE SUPPLIES LAST)
#AM-5008/200ALC - 200cc aluminum cup - $28.00
#AM-5008/400ALC - 400cc aluminum cup - $28.00
#AM-5008/600NYC - 600cc nylon cup - $30.00
#AM-5008/600ALC - 600cc aluminum cup - 32.00
#AM-5008/1000ALC - 1000cc aluminum cup - 35.00

AM-8008/5008 "SmartPak" - We almost called this package the "Not Sure Which Spray Gun To Get-Kit". This package contains both a small gravity detail gun and a full size gravity gun. Both are LVLP guns and will work with small compressors. The 1.4mm setup in the large gun will handle clears and the small gravity gun with 1.0mm is perfect for stains, sealers and most clear finishes (some may require thinning). The two cups have adapters so you can use both cup sizes with either gun, and included are rebuild/service kits, mini-regulator and cleaning brushes. What a great deal this package is if you don't know whether to get a full size or detail gun. Both guns incorporate stainless steel in the fluid passages, threaded connector to the cup, and the female connector in the nylon cup. This upgrade by our factory insures proper performance with waterborne finishes and catalyzed solvent products.

Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Cups: 125cc and 600cc
Working Pressure : 29 psi (at gun inlet)
Air Consumption: 3 cfm (detail gun) 5.5 cfm (large gun)
Needle/nozzle/air cap: 1.0mm (detail gun), 1.4mm (large gun)

SP-08 If you attend my classes, you'll see me use this gun quite a bit. You'll love this touch up gun for its price, but it's perfect for working up samples, toning, shading and small projects. The overhead trigger makes for precise detail work and is very comfortable to use. While not HVLP, it will work fine with small compressors. Stainless steel needle and nozzle make it perfect for water based. Standard configuration of 1.6mm will handle all stains and thin clears like shellac and lacquer. Water base finishes need 10% thinning with water. Package includes gun, 8 oz. cup and complete instructions. If you use this gun for dyes and toners like I do, be sure to get several extra cups!

Body: nickled brass
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Cup: Aluminum 8 oz.
Working Pressure : 30-50 psi (at gun inlet)
Air Consumption: 2.8 - 4 cfm
Needle/nozzle/air cap: 1.6mm

#QS08 - $37.50
#QS08-KIT - $55.00 (Includes QS08 and QS813 Cleaning Kit)
#QS08CUP - $8.00 (8 oz cup assembly - includes lid and yoke assembly)

SP-200 This is a low pressure HTE gun that surprised us when we tested it here against guns 3 times the cost. This lightweight, smaller footprint gun features low air consumption and affordability. Runs easily with smaller compressors. Team this up with our new 3M PPS HO Cup and you have a real winner. A built in air micrometer lets you control the air at the gun, Your choice of 1.2mm, 1.4mm, or 1.8mm will handle all your requirements. Get the 1.2mm for most clears, and the 1.4mm for thicker clears and the 1.8mm for latex. Positively the best value for the buck! Choose from various configurations below or customize your own. Gun package includes wrench, cleaning brush and complete instructions.

Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Working Pressure : 30-40 psi (at gun inlet)
Air Consumption: 4 cfm
Needle/nozzle/air cap: 1.2, 1.4, and 1.8mm.

#SP-200 - $99.00 (gun only)
#SP-200/S - $119.00 (suction feed 1.8mm only)

#SP-200-KIT- #1 - $239.00 (Includes SP-200 and 2 qt Qualspray pressure pot and 5' rubber hoses)
Note: for a great way to spray latex, get this configured with the 1.5mm!!!
#SP-200-KIT- #2 - $429.00 (Includes SP-200 and 1 gallon QualSpray pressure pot and 15' hoses)
#SP-200-KIT- #3 - $489.00 (Includes SP-200 and 2.5 gallon QualSpray pressure pot and 25' hoses)

#SP-20012 - 1.2mm NN kit for SP-200 - $58.00
#SP-20014 - 1.4mm NN kit for SP-200 - $58.00
#SP-20015 - 1.5mm NN kit for SP-200 - $58.00

Special - Get the new SP-200 with the 3M PPS HO 1 quart cup system. Includes gun, 1 extra NN set, pressure regulator for cup, 1 Qt HO cup with collar, PPS adapter, and 25 lids and liners. With this system, spray any finish you want, even upside down! Absolutely blows away any other rig on the market!

Includes SP-200 gun, 1 extra NN set, QS-32SRA regulator, #18 PPS adaptor (#16054), #16124 HO 1 qt cup, collar, and strainer, and #16024 box 25 lids and liners.

QS-1000T - Need an extra spray gun for your turbine system? Or just replace your existing one? This affordable HVLP bleeder style turbine gun from QualSpray will work with any turbine system out there. Features 1 quart cup with stainless pickup tube, cam-lock cup and large fluid control knob. 1.3mm nozzle will handle any finish except maybe latex paint.

Cup: Aluminum 1000cc
Nozzle/needle: stainless steel
Air cap: aluminum
Gaskets: Teflon
Needle/nozzle/air cap: 1.3mm

#QS-1000T - $119.00