New!!  - All stainless-steel construction is traditionally expensive, but we've solved that problem with our all-new 1 qt Homestead exclusive! Upgrade your current cup whether it's an old style suction feed or pressure feed. This is the cup to use with water based finishes! Can replace any cup with a traditional 3/8" NPS fluid fitting. Features an EPDM* solvent proof gasket and cam lock closure. more............

Now you don't have to worry about leaving water based finishes in the cup - whether it's all day or all week. Traditional aluminum cups not only  can react with some water based finishes, but they also are hard to clean. Water based finishes are much easier to clean from stainless steel, particularly latexes and the pigmented lacquers and polyurethanes.

* EPDM - ethylene propylene diene monomer, a synthetic rubber gasket that is more solvent proof and softer than typical hard Teflon gaskets used in 1 qt cups.

QualSpray DP-1SS If you are tired of the hassles of using a pressurized pot, or want a simple and convenient way to spray finishes from larger containers, you should consider a double diaphragm pump setup. These setups use air from your compressor  (only 6 cfm required) to power a low maintenance pump to siphon finish from your finish container and deliver it to your spray gun.  more............

New!  AM - "SmartPak" Series -  The AM-Series SmartPaks contain all the nozzle sets you need to spray finishes. Choose from either the AM-6008 pressurized siphon 1 Qt Cup or the AM-5008 Gravity Gun.  What a great deal this package is if you don't know what nozzles to get for you new gun. Gun incorporates stainless steel in the fluid passages and other key fluid contact points. This upgrade by our factory insures proper performance with waterborne finishes and catalyzed solvent products.

Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Working Pressure : 29 psi (at gun inlet)
Air Consumption: 6 cfm
 

AM-6008/1QT - Gun with 1 qt pressurized cup (shown right), 1.0mm, 1.3mm, 1.5mm NN setups, repair kit, strainers, service wrench - $299.00
 

AM-5008 - Gun with 600cc cup (shown left) 1.5mm, 1.8mm, 2.5mm NN setups, repair kit, strainers, service wrench - $269.00
 

more on these 2 guns.....

QS-1000T - Need an extra spray gun for your turbine system? Or just replace your existing one? This affordable HVLP bleeder style turbine gun from QualSpray will work with any turbine system out there. Features 1 quart cup with stainless pickup tube, cam-lock cup and large fluid control knob. 1.3mm nozzle will handle any finish except maybe latex paint. more........

New!! - Economy Rubber Air Hose with Hi-Flo HVLP Fittings
Red air hose is 1/4" (inside diameter) This tough rubber hose comes with our Hi-FLO HVLP quick disconnects installed and are compatible with most other systems like Porter-Cable, Campbell Hausfeld and others.  

Economy Rubber Fluid Hose - 1/4"
#5515 - Fluid hose 15' - 25.00
#5525 - Fluid hose 25' - 35.00

QualSpray Disposable In-line Filter - this filter removes oil, water, rust, dirt and other particles that get through other downstream filters. It's designed for low restriction of air so you can install it right at the gun and won't affect low pressure guns like LVLP and HVLP. A very economical way to remove the last trace of contaminants before they enter the gun. 

#F3 - PRICE: $3.75 (each)
 

New!! Ford #4 Economy Viscosity Cup for precise measurement of finish viscosity. Differs from above with a shorter handle and plastic orifice. Similar to cups shipped with Turbine systems like Fuji.

#QS-817 - Economy Viscosity Cup Ford #4 - $5.00

BACK TO TOP